How To Install Pvc Wall Panels

Skip to content

How to install PVC Wall and Ceiling Panels

Tools you lot will demand:

1. 1. Tape measure
   2. Spirit Level
   3. Fine tooth saw or Stanley knife
   4. Silicone sealant and special gum for PVC panel
   5. Console agglutinative
   6. Not corrosive staples 14mm long, or non-corrosive nails/screws.
   7. Staple gun, hammer, screwdriver
   8. Mitre Block

1. Beginning with the Ceiling

Beginning measure the console carefully before cut.

2. Use a abrupt Stanley blade or fine-molar saw to cut the panels to the right length.

Our panels are quickly and easilycut to length.

3. Use a good amount of adhesive on the back of the console.

We recommend using Top Gun adhesive.

4. If using battens over the surface, screw, staple or pin through the tongue of the panel every 30cm

There is no need for wall plugs. Echo this procedure for the rest of the ceiling panels.
The tongue and groove organisation allows each panel to slot neatly into 1 some other.

5. Side by side, measure out for your finishing trims around baths and shower trays

Mensurate from the corner of the bath to the cease on both sides.

6. Cut the clad seal strips to the correct length and use the mitre block to cut the angles for the corners.

Clad seal strips ensure a water tight seal between the panels and the bath or bear witness tray.

Place the strips in position to brand certain they fit correctly. Using the alcohol wipes, wipe the surface of the bath where the strip will sit.

seven. Apply CladSeal adhesive to the bottom of the clad seal strip and smooth out with the spatula.

A special type of adhesive is used with the clad seal strips which guarantees water tightness.

viii. Utilize the CladSeal adhesive along the surface of the bath and forth the wall.

9. Then fit the strip to the surface of the bath allowing the silicone on the strip to bail with the silicone on the bath to grade a waterproof seal.

The corners where ii strips connect can also be sealed at this point. Screws can exist used to lock the strip to the wall and stop it moving.

10. Before mounting the wall panels, fix the one piece internal corner trim. Remove the protective film, utilize silicone and adhere to the corner of the wall.

Internal corner trims are used to bring together two panels every bit they meet an internal corner

11. Place the commencement console

• Measure from where the panel will sit with the ceiling and cut the panel to the correct length.
• Remove whatever protective flick and utilize agglutinative to the back of the panel. Utilise adhesive to the back of the panel before placing the panel.
• If y'all have uneven walls, additional agglutinative tin be used to compensate for this. In the example of very uneven and damp surfaces, we recommend using anti-rot battening. This should be spaced 25-40 cm apart and fixed horizontally for vertical console installations.
• Use a spirit level to ensure batten are apartment and level. Panels can exist fixed to the battens at the panel tongue using non corrosive nails, screws or staples.
• Utilise silicon to the groove of the internal corner trim and then slot the first panel into this for a waterproof terminate.

12. If walls are uneven, check that the panel is straight and and then if necessary, utilize a staple gun, pin or spiral through the tongue on to the batten which volition forbid movement whilst the adhesive sets.

While the adhesive will concord these panels in place in most cases, it may be required to screw panels into battens if the wall surface is uneven.

13. Apply a skillful amount of adhesive on the dorsum of each panel before mounting.

If any silicon seeps out onto the surface of the panel, remove it immediately with a damp fabric..

fourteen. Use silicon to the groove of the first panel before slotting in the second one to seal information technology.

If whatsoever silicon seeps out onto the surface of the console, remove it immediately with a damp cloth.

Panels can be glued directly onto and over existing firm, clean and dry out substrates, example plaster boards, plywood, tiles, paint etc.

15. Echo this procedure for the residual of the wall.

16. The easiest way to fit the one part coving is to remove the lip from the dorsum with a Stanley knife.

Measure carefully earlier cutting the coving to the right length and use the mitre block for the corners. Check that the corners fit tightly before applying adhesive.

The coving tin can and so be stuck directly to the wall and ceiling using a combination of silicone and double sided tape.

17. For a professional job use our finishing trims to finish corners and edges.

Ensure that the room is properly ventilated for 24 hours.

Permit 24 hours for the silicone sealant to fully dry.

Login

This site uses cookies to offer you a better browsing experience. Past browsing this website, you concur to our use of cookies. Cookies are used for ads personalisation.

Source: https://allpanels.co.uk/panel-installation-guide/

Share this post